Shopping Cart
Empty
Oil Nozzle Joint
Oil Nozzle Joint is intended for the end user elements in an system, i.e. for connecting the central lubrication system with elements such as bearings, spindles, linear guideways and sliding surfaces.
High Pressure Tube
Details
Details
| Model | D | d | S | L | SKU | Compatibility |
| PL404 - Angle Joint | M4x0.7 | M8x1 | 18 | 12 | 1189001 | Any type of Pipe ∅ 4mm / HGR15 |
| PL406 - Angle Joint | M6x1.0 | M8x1 | 18 | 12 | 1189002 | Any type of Pipe ∅ 4mm / HGR20/25/30/35/40 / SFU16/20/25/32 SCS / SBR |
| Dimensions for Angle Joint |  |
|||||
| Model | D | d | S | L | SKU | Compatibility |
| PD404 - Direct Joint | M4x0.7 | M8x1 | 10 | 12 | 1189011 | Any type of Pipe ∅ 4mm / HGR15 |
| PD406 - Direct Joint | M6x1.0 | M8x1 | 10 | 12 | 1189012 | Any type of Pipe ∅ 4mm / HGR20/25/30/35/40 / SFU16/20/25/32 / SCS / SBR |
| Dimensions for Direct Joint |  |
|||||
| PD Direct Joint and PL Angle Joint is sold as a set of 3 parts 1. PD404/406 - Direct Joint + PA-4 Nut + PB-4 Ball Bushing 2. PL404/406 - Angle Joint + PA-4 Nut + PB-4 Ball Bushing This configuration is defined for use with any pipe (Copper , Alu or Plastic) ∅ 4mm |
 |
|||||
| For other dimensions, threads and diameter of the inlet hose, send an request to email. | ||||||
| Pictures, dimensions,table data and technical drawings of this product are made with reasonable care and liability is excluded for the accuracy and correctness of this data. | ||||||
Oil Nozzle Joint is intended for the end user elements in an system, i.e. for connecting the central lubrication system with elements such as bearings, spindles, linear guideways and sliding surfaces.
VERY IMPORTANT: Ensure proper plastic hose fitting tightening to avoid common mistakes.
1. The appearance of a ferrule that is not tightened enough to hold the hose tight so it doesn't fall out or leak.
2. The appearance of a ferrule that is clamped tightly enough that the hose cannot fall out and there is no leakage. At the end, pull the hose strongly with your hand and if it stays in position, then it's ok.
VERY IMPORTANT:
Tighten the fittings nut by hand until you feel that the screw socket, ferrule and opposite nut are pressed together. This is done only when it comes to plastic hoses, with copper and aluminum hoses you can tightening with less force.
A simple diagram of the Centralized Lubrication System
Description and SKU catalog numbers of Centralized Lubrication System elements from the diagram
- Oil station unit (used for large systems for lubrication)
- Standard electric pump for Centralized Lubrication System SKU 1191000
- Hand Lubrication Pump for simple Centralized Lubrication System SKU 1192000
- Oil stop plug, end terminal, can be used to terminate any input, end or output terminal. Oil Sealing Plug SKU 1190001 - 1190002
- Stainless steel Spring Tube Protector SKU 1187001 + 1187021
- Oil T-Distributor SKU 1188012 , 1188013
- Oil Pipe Fittings / PA-6 Nut or PA-4 Nut SKU 1185002 or 1185001
- Oil Pipe Fittings / PB-6 Ball Bushing or PB-4 Ball Bushing SKU 1185012 or 1185011
- Oil Nozzle Joint / PD40X - Direct Joint / start from SKU 1189011 (PD404 - Direct Joint mostly used for HGH/HGW15)
- Oil Nozzle Joint / PL40X - Angle Joint / start from SKU 1189001 (PL404 - Angle Joint mostly used for HGH/HGW15)
- Oil Divider Bridge / M10x1 SKU 1195000
- Volumetric Oil Distributor start from SKU 1194001 (on diagram is shown model: VOD-05-Volumetric / 1194005)
- Oil separator block / start from SKU 1193001 (on diagram is shown model: A-06-10-Oil-Separator / 1193003)
- / Oil Resistance Dispenser nozzle fittings (ask for availability)
- / Oil Resistance Dispenser nozzle on side of lubrication point (ask for availability)
- / Oil Resistance Dispenser nozzle on side of lubrication point behind lubrication brush (ask for availability)
- / Oil Resistance Dispenser nozzle (ask for availability)