Shopping Cart
Empty
TB67S Stepper Driver
TB67S 4A Single Axis MicroStepping Stepper Motor Driver Controller based on Toshiba TB67S109AFTG Chip.
TB67S109AFTG is 2nd generation PWM chopper-type single-chip bipolar sinusoidal micro-step stepping motor driver. This 4A drive is better than HY-268N-DIV-5A stepper drive. This 2-phase bipolar-type stepping motor can be driven by only clock signal with low vibration and high efficiency and low heat generation. Suitable for drive Two-phase stepping motor dynamic voltage 9V to 40V, the maximum drive current is less than 4A.
TB67S109AFTG is 2nd generation PWM chopper-type single-chip bipolar sinusoidal micro-step stepping motor driver. This 4A drive is better than HY-268N-DIV-5A stepper drive. This 2-phase bipolar-type stepping motor can be driven by only clock signal with low vibration and high efficiency and low heat generation. Suitable for drive Two-phase stepping motor dynamic voltage 9V to 40V, the maximum drive current is less than 4A.
Price without tax:6,50 €
Mach3 5-Axis Board
Power Supply SW
DM556 Stepper Driver
DM860H Stepper Driver
Technical Details
NOTE: this driver is sold everywhere as TB6600 which is not true, this driver use TOSHIBA TB67S109AFTG chip (see download tab to check TB67S109AFTG data sheet). By technical and electrical characteristics it has a lot of similarities with TB6600 and both models are made by TOSHIBA .
| Pin | Pin Name | Description | |
|---|---|---|---|
| 1 | ENA- (ENA) | Enable Input (Cathode of Optocoupler) |  |
| 2 | ENA+ (+5V) | Enable Input (Anode of Optocoupler) | |
| 3 | DIR- (DIR) | Direction Input (Cathode of Optocoupler) | |
| 4 | DIR+ (+5V) | Direction Input (Anode of Optocoupler) | |
| 5 | PUL- (PUL) | Step Pulse Input (Cathode of Optocoupler) | |
| 6 | PUL+ (+5V) | Step Pulse Input (Anode of Optocoupler) | |
| 7 | B- | Motor Winding Phase B - | |
| 8 | B+ | Motor Winding Phase B+ | |
| 9 | A- | Motor Winding Phase A - | |
| 10 | A+ | Motor Winding Phase A+ | |
| 11 | GND | Power Supply Input Negative / 0V GND | |
| 12 | VCC | Power Supply Input Positive / 9V to +40V | |
WORKING Specifications
- Input voltage DC 8 ~ 50Vmax input (Operating Voltage: 9V – 40V)
- The input current of 1 to 4 amps
- Output current:
- IOUT= 4.0 A (absolute maximum ratings, peak)
- IOUT= 3.5 A (operating range, maximal value)
- Built-in thermal protection (TSD) circuit
- Built-in voltage protection (UVLO) circuit
- Built-in over current detection (ISD) circuit
- Control signal Inputs: +5V<20ma optically="" isolated="" li="">
- With auto standby function (low motor heat in standby)
- Selectable microstepping resolution (1/1, 1/2, 1/4, 1/8, 1/16 1/32 step)
- Suitable for step motor:NEMA(17,23,32) 42, 57 and 86 type 2 phase 4 phase (4 / 6 / 8 wires)
- LED indicator for Power ON / Alarm (error)
- Operating Temperature: -10 to 45 ℃
- Storage temperature: -40 ℃ to 70 ℃
MICROSTEP / Current Limit Selection
| MicroStep Selection DIP Switch | Current Limit Selection DIP Switch | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Step | Pulse/rev | S1 | S2 | S3 | I out(A) | Peak(A) | S4 | S5 | S6 | |||
| NC* | NC | on | on | on | 0.5 | 0.7 | on | on | on | |||
| 1 | 200 | on | on | off | 1.0 | 1.2 | on | off | on | |||
| 2/A** | 400 | on | off | on | 1.5 | 1.7 | on | on | off | |||
| 2/B*** | 400 | off | on | on | 2.0 | 2.2 | on | off | off | |||
| 4 | 800 | on | off | off | 2.5 | 2.7 | off | on | on | |||
| 8 | 1600 | off | on | off | 2.8 | 2.9 | off | off | on | |||
| 16 | 3200 | off | off | on | 3.0 | 3.2 | off | on | off | |||
| 32 | 6400 | off | off | off | 3.5 | 4.0 | off | off | off | |||
* Standby mode (output stage is set to ‘OFF’ status)
** 1/2A type (1-2 phase excitation A type) (0%, 100%)
*** 1/2B type (1-2 phase excitation B type) (0%, 71%, 100%)
Pictures, dimensions,table data and technical drawings of this product are made with reasonable care and liability is excluded for the accuracy and correctness of this data.
Description
BASIC Description
TB67S109AFTG is 2nd generation PWM chopper-type single-chip bipolar sinusoidal micro-step stepping motor driver. This 4A drive is better than HY-268N-DIV-5A stepper drive. This 2-phase bipolar-type stepping motor can be driven by only clock signal with low vibration and high efficiency and low heat generation. Suitable for drive Two-phase stepping motor dynamic voltage 9V to 40V, the maximum drive current is less than 4A.
This drive uses the current loop subdivision control, the motor torque ripple is very small, low-speed running is very smooth. High-speed torque is much higher than other two-phase drives, high positioning accuracy. Widely used in the engraving machines, CNC machine tools, packaging machinery and other high resolution requirements on the device. NEMA17, NEMA23, NEMA24 and NEMA34 stepper motors work perfectly with this 4A Stepper Driver.
FEATURES
The TB67S109A is a two-phase bipolar stepping motor driver using a PWM chopper. The clock in decoder is built in. Fabricated with the BiCD process, rating is 50Vmax / 4.0 A .
- PWM constant current drive single-chip bipolar sinusoidal micro-step stepping motor driver
- Selectable excitation mode (1/1, 1/2, 1/4, 1/8, and 1/16 step)
- Single power supply
- Average current control (in 8 steps from 0.5A to 3.5A), two-phase sinusoidal current drive output
- DC 9 ~ 40V Single power supply operation
- Optically isolated inputs
- Over voltage, under-voltage, over-current, and short-circuit protection
- High starting speed
- High-speed torque
- Black Rugged All metalic Enclosure and Large Black Aluminium Heat Sink
- Mounting Holes on Heat Sink for Mounting the Drive in Machine Panels
- High efficiency motor current control mechanism ADMD (Advanced Dynamic Mixed Decay)
- Weight 130g